Cat Wheel Dozers: 854

ტექნიკური მახასიათებლები

Engine

Engine Model	— Cat C32B Cat C32B
Gross Power	— 907 hp 676 kW
Emissions (U.S. EPA Tier 4 Final): Gross Power - SAE J1995	— 900 hp 671 kW
Emissions (U.S. EPA Tier 4 Final): Net Power ISO - 9249	— 814 hp 607 kW
Emissions (Tier 2 Equivalent): Gross Power - SAE J1995	— 907 hp 676 kW
Emissions (Tier 2 Equivalent): Net Power ISO - 9249	— 823 hp 614 kW
Rated Speed	— 1750 r/min 1750 r/min
Bore	— 5.7 in 145 mm
Stroke	— 6.4 in 162 mm
Displacement	— 1958 in² 32.1 l
Peak Torque - 1,200 rpm	— 3139 lb/ft 4242 N·m
Torque Rise	— 30 % 30 %
Note (1)	— Net power advertised is the power available at the flywheel when the engine is equipped with fan, air cleaner, muffler and alternator. Net power advertised is the power available at the flywheel when the engine is equipped with fan, air cleaner, muffler and alternator.
Note (2)	— Net torque rise meets SAE J139. Net torque rise meets SAE J139.
Note (3)	— No engine derating required up to 3050 m (10,000 ft) altitude. No engine derating required up to 3050 m (10,000 ft) altitude.

Weights

Operating Weight	— 224647 lb 101898 kg

Transmission

Transmission Type	— Cat Planetary Power Shift Cat Planetary Power Shift
Converter Drive - Forward 1	— 4.4 mile/h 7.1 km/h
Converter Drive - Forward 2	— 7.7 mile/h 12.4 km/h
Converter Drive - Forward 3	— 13.2 mile/h 21.2 km/h
Converter Drive - Reverse 1	— 4.8 mile/h 7.7 km/h
Converter Drive - Reverse 2	— 8.4 mile/h 13.5 km/h
Converter Drive - Reverse 3	— 14.6 mile/h 23.5 km/h
Direct Drive - Forward 1	— Lock-up disabled Lock-up disabled
Direct Drive - Forward 2	— 8.1 mile/h 13 km/h
Direct Drive - Forward 3	— 14.2 mile/h 22.8 km/h
Direct Drive - Reverse 1	— 5 mile/h 8 km/h
Direct Drive - Reverse 2	— 8.9 mile/h 14.3 km/h
Direct Drive - Reverse 3	— 15.6 mile/h 25.1 km/h
Note	— Travel speeds based on 45/65-45 L-5 46 ply tires. Travel speeds based on 45/65-45 L-5 46 ply tires.

Hydraulic System - Lift/Tilt

Output at 1,850 rpm and 6900 kPa (1,000 psi)	— 161 gal/min 610 l/min
Cylinders, Double Acting - Lift, Bore and Stroke	— 177 mm × 1760 mm (0.58 ft × 5.8 ft) 177 mm × 1760 mm (0.58 ft × 5.8 ft)
Cylinder, Double Acting - Tilt and Tip, Bore and Stroke	— 267 mm × 286 mm (0.88 ft × 0.94 ft) 267 mm × 286 mm (0.88 ft × 0.94 ft)

Service Refill Capacities

Fuel Tank - Standard	— 413 gal (US) 1562 l
Cooling System	— 53 gal (US) 200 l
Crankcase	— 32 gal (US) 120 l
Transmission	— 45 gal (US) 169 l
Differential - Final Drives - Front	— 98 gal (US) 369 l
Differential - Final Drives - Rear	— 90 gal (US) 342 l
Hydraulic System - Steering and Engine Cooling Fan - Tank Only	— 77 gal (US) 290 l
Note (1)	— - All nonroad U.S. EPA Tier 4, European Union (EU) Stage IIIB and V, and Japan (MLIT) Step 4 diesel engines are required to use only Ultra Low Sulfer Diesel (ULSD) fuels containing 15 ppm (mg/kg) sulfer or less. Biodiesel blends up to B20 (20% blend by volume) are acceptable when blended with 15 ppm (mg/kg) sulfer or less ULSD. B20 should meet ASTM D7467 specification (biodiesel blend stock should meet Cat biodiesel spec, ASTM D6751 or EN 14214. Cat DEO-ULS or oils that meet the Cat ECF-3, API CJ-4, and ACEA E9 specification are required. For further fluid specifications and guidelines, visit: http://parts.cat.com/cda/files/3244668/7/SEBU6250-19.pdf - All nonroad U.S. EPA Tier 4, European Union (EU) Stage IIIB and V, and Japan (MLIT) Step 4 diesel engines are required to use only Ultra Low Sulfer Diesel (ULSD) fuels containing 15 ppm (mg/kg) sulfer or less. Biodiesel blends up to B20 (20% blend by volume) are acceptable when blended with 15 ppm (mg/kg) sulfer or less ULSD. B20 should meet ASTM D7467 specification (biodiesel blend stock should meet Cat biodiesel spec, ASTM D6751 or EN 14214. Cat DEO-ULS or oils that meet the Cat ECF-3, API CJ-4, and ACEA E9 specification are required. For further fluid specifications and guidelines, visit: http://parts.cat.com/cda/files/3244668/7/SEBU6250-19.pdf

Axles

Front	— Fixed Fixed
Rear	— Trunnion Trunnion

Brakes

Brakes	— Meets ISO 3540:2011 Meets ISO 3540:2011

Blades

Blade Capacities	— 30.5 to 44.8 m3 (40 to 58.6 yd3) 30.5 to 44.8 m3 (40 to 58.6 yd3)

Dimensions (Approximate)

Height - Top of ROPS	— 18.25 ft 5590 mm
Height - Top of Exhaust Pipe	— 17.17 ft 5234 mm
Height - Top of Hood	— 13 ft 3984 mm
Ground Clearance	— 27 in 691 mm
Centerline of Front Axle to Hitch	— 9.67 ft 2945 mm
Centerline of Rear Axle to Edge of Bumper	— 13.75 ft 4195 mm
Wheel Base	— 19.25 ft 5890 mm
Length - With Blade on Ground	— 44 ft 13405 mm

Hydraulic System - Steering

Steering System - Pump	— Piston, variable displacement Piston, variable displacement
Minimum Turning Radius - Over Blade	— 31 ft 9550 mm
Steering System - Circuit	— Pilot, load sensing Pilot, load sensing
Total Steering Angle	— 86 degrees 86 degrees
Relief Valve Setting	— 5004 psi 34500 kPa

Operating Specifications

Operating Weight	— 224647 lb 101898 kg

Sound Performance Levels

Sound Performance	— • The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. • The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. • Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment. • The machine sound power level was measured according to ISO 6395:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. • The operator sound pressure level was measured according to ISO 6396:2008. The measurement was conducted at 70 percent of the maximum engine cooling fan speed. • Hearing protection may be needed when the machine is operated with a cab that is not properly maintained or when the doors or windows are open for extended periods or in a noisy environment.

Air Conditioning System

Air Conditioning	— The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes. The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 1.8 kg of refrigerant which has a CO2 equivalent of 2.574 metric tonnes.

Cab

ROPS/FOPS	— ISO 3471:2008 and ISO 3449:2005 Level II Standards ISO 3471:2008 and ISO 3449:2005 Level II Standards

უპირატესობები და მახასიათებლები

Safety

Improved visibility, with pull-down window shade, optional heated mirrors, standard HID lights, and cab-mounted LED warning beacons.
Optional Detect with Object Detection System (rear-view camera and radar) or Vision (rear-view camera) for enhanced visibility.
Improved access and egress, with wide stairs and reduced angles; windshield cleaning platforms; emergency egress; plus the safe, ergonomic Cat powered access system, which can be raised and lowered from the cab level or the ground.
Wide walkways with non-skid surfaces, integrated lockout/tagout points, and ground-level or platform-accessible service areas.

Operator Comfort

Soft detent Electro-Hydraulic Controls, which are easy to use, and electronically controlled hydraulic cylinder stops that boost comfort.
Pressurized cab with filtered air, automatic temperature controls, viscous cab mounts and seat air suspension for reduced vibration and reduced sound levels.
Cat Comfort Seat, with high back design, extra thick contoured cushions, air suspension system, easy-to-reach seat levers and controls for six-way adjustments, and seat-mounted implement pod and STIC steer that moves with the seat.
Standard fold-down trainer seat with drink tray, storage, and wide, retractable seat belt.
Personalized machine feature settings, including ability to instantly recall up to 10 profiles stored in Advisor Display.

Productivity

Load-sensing hydraulic steering system, which helps operators achieve precise positioning for easy loading in tight areas with 43 degrees of steering articulation.
Impeller Clutch Torque Converter (ICTC) and Rimpull Control System (RCS), which improve rimpull and reduce tire slippage and wear and improve fuel efficiency in certain applications.
Cat Planetary Powershift Transmission for consistent, smooth shifting and efficiency through integrated electronic controls, with three forward and three reverse speeds
Steering and Transmission Integrated Control System (STIC™), which combines directional selection, gear selection and steering into a single lever — for maximum responsiveness and control.
Cat C32B engine that delivers on-demand performance through the use of turbochargers and aftercoolers, with a 33% torque rise that ensures high lugging forces during digging and acceleration in high rimpull conditions.

Serviceability

Reduced time spent on regular maintenance procedures thanks to features such as ground-level or platform access to filters, grouped service points and swing-out doors on both sides of the engine compartment.
Standard VIMS™ 3G monitoring system with easy-to-view display that delivers critical health and payload information, keeping performance at optimum levels and allowing advanced troubleshooting and planning to lower maintenance costs.
Extended performance and reliability thanks to advanced filtration system.

Durability

Full box-section frames that absorb torsional forces during dozing, maintaining alignment for hitch pins and drive line.
Spread hitch design featuring double tapered roller bearings and hardened pins that resist both horizontal and vertical loads.
Enhanced strength in key pin areas through the use of one-piece castings, and solid one-piece push beams that are through-width, not merely attached to the side of the frame.
90 percent of the machine structure is robotically welded to provide highly consistent welds and increased strength.
Frame, powertrain, engine and components that all built to be rebuilt — using new, remanufactured or rebuilt parts and components — to deliver multiple lives of like-new performance at a fraction-of-new price.

Technology

Cat MineStar™ Terrain for loading, which provides real-time feedback on payloads and design plan progress to increases productivity and accuracy, reduce rework, enhance ore control and improve shift-to-shift operator performance.
MineStar Detect, with offers a range of capabilities designed to assist the operator with areas of limited visibility around fixed and mobile equipment.
MineStar Health, which delivers critical event-based machine condition and operating data and includes comprehensive equipment health and asset monitoring capabilities, with a wide range of diagnostic, analytic and reporting tools.
Upgraded touchscreen information display that provides intuitive operation and easy navigation and keeps operators informed about machine systems to decrease service time.

Sustainability

Designed to be more efficient and use less fuel, which reduces engine emissions and carbon footprint; Tier 4 Final engine reduces NOx and particulate matter.
Engine Idle Shutdown, which saves fuel by making it possible to avoid unnecessary idling.
Reduced waste with maintenance-free or extended-maintenance batteries, and better control of fluids through use of ecology drains.
Retrofits and upgrades for older machines — to incorporate efficiency improvements and emission reductions, and to keep them in production longer to conserve energy and minimize the need for raw materials
Cat Rebuild and Cat Reman programs, which preserve raw materials, conserve energy and reduce emissions.

აღჭურვილობა

სტანდარტული ტექნიკა

ELECTRICAL AND LIGHTING
- Alternator, 150 amp
- Batteries, maintenance free (4 – 1,400 CCA)
- Battery disconnect and jump start receptacle, bumper
- Deutsch terminal connectors
- Electrical system, 24V
- Electronic transmission control
- Lighting system, halogen (front and rear) lighting, access stairway, engine compartment
- Starter lockout in bumper
- Starting and charging system, 24V
- Transmission lockout in bumper

POWERTRAIN
- Brakes, oil cooled, multi-disc, service/secondary
- Engine brake
- Engine, Cat C32B
- Fuel priming pump (electric)
- Ground level engine shutoff
- Axle oil coolers (front and rear)
- Pre-cleaner, engine air intake (above hood)
- Radiator, Aluminum Modular (AMR)
- Starting aid, (ether) automatic
- Throttle lock electronic
- Torque converter, impeller clutch with lock-up clutch (ICTC) and rimpull control system
- Transmission, 534 mm (21 in) planetary power shift (electronic) (3F/3R)

OPERATOR ENVIRONMENT
- Advisor display, displays real time operating information, performs calibrations and customizes operator setting
- Air conditioner and heater with automatic temperature control
- Air pre-cleaner, powered
- Cab, sound-suppressed pressurized, separate external rollover protective structure (ROPS/FOPS)
- Cigar lighter and ashtray
- Coat hook
- Converter (12V, 10-15 amp) and power port
- Digital display on center console: gear, ground speed, machine hours
- Electro-hydraulic blade controls, joystick
- Heater and defroster
- Horn, electric
- Instrumentation, gauges: engine coolant temperature, fuel level, hydraulic oil temperature, powertrain oil temperature, tachometer
- Instrumentation, warning indicators: action alert system – three categories, automatic transmission model enable status, brake malfunction, bucket float status, delayed engine shutdown status, engine idle shutdown status, engine malfunction, fuel economy mode enable status, hydraulic lockout, lockup clutch enable status, low fuel level, parking brake status, rimpull control enable status, seat belt warning, secondary steering (if equipped), throttle lock status, transmission gear
- Light, cab, dome
- Lunchbox and beverage holders
- Premium seat with heated and actively cooled leather, adjustable lumbar support, air adjustable bolsters on the seat and backrest, seat cushion tilt adjustment, and adjustable-length seat cushion
- Radio, AM/FM with Bluetooth®, USB Port, 3.5 mm (0.14 in) auxiliary (AUX) input
- Tinted glass
- Wet-arm wipers/washers (front, rear, and corner) – intermittent front wiper

SAFETY
- Alarm, back-up
- Camera, rear vision
- Emergency platform egress
- Implement lock out switch
- LED warning strobe
- Mirrors, rearview (externally mounted)
- Seat belt, retractable, 76 mm (3 in) wide
- Separate external protective structure (ROPS/FOPS)
- Stairway, left and right rear access
- Steering and transmission lock lever, cab
- Steering, secondary
- Seat, trainer with lap belt,
- 76 mm (3 in) wide
- Toe kicks

SERVICE
- Automatic Lubrication System greases the hitch, steering, and axle trunnion bearings
- Axle ecology drains
- Battery disconnect and jump start receptacle, bumper
- Case drain filters
- Coupling, Cat O-ring face seals
- Engine, crankcase, 500 hour interval with CH4
- Front walkway around cab
- Guards, crankcase and power train
- Ground-level fast fill fuel system
- Ground-level service center with Electronic Technician (ET) port, fast fill fluid ports, ecology drains
- Grouped/Labeled lube points
- Hitch, drawbar with pin
- Hoses, Cat XT™
- Oil sampling valves
- Starter and Transmission lockouts in bumper
- Sight gauges for steering, implement and transmission oil
- Vital Information Management System (VIMS™) 3G with graphical information display: external data port, customizable operator profiles

COOLING
- Standard ambient package (recommended for site conditions that do not exceed 43° C [110° F])

COLD WEATHER
- Heated Seat

EFFICIENCY
- Economy mode with on-demand throttle
- Positive Flow Control implement system
- Impeller Clutch Torque Converter (ICTC) with lock-up clutch
- Load-sensing steering
- Soft detent controls
- Engine idle management features: auto idle kickdown, delayed engine shutdown, engine idle shutdown

TRAMMING
- Front Fenders

აირჩიეთ ტექნიკა

ELECTRICAL AND LIGHTING
- Lights, HID
- Lights, LED
- Product Link (Cellular)
- Product Link (Satellite)

POWERTRAIN
- Driveline parking brake
- No spin rear axle
- Pre-cleaner, raised

OPERATOR ENVIRONMENT
- Radio, Sirius XM/AM/FM radio with Bluetooth technology, USB Port, 3.5 mm (0.14 in) AUX input
- Rubber mounted cab glass
- Window sun screen

SAFETY
- Egress, powered rear access
- Object detection (radar)
- Wheel Chocks

SERVICE
- High pressure hydraulic oil screen
- Product Link™
- Tire pressure monitoring

BLADES
- Semi-U, 30.5 m3 (40 yd3) HD Semi-U, 30.5 m3 (40 yd3) Coal, 44.8 m3 (58.6 yd3)
- Paint, black blade rear

COOLING
- High ambient cooling system (recommended for ambient temperatures up to 50° C [122° F] for EPA Tier 4 Final emissions certified machines and 55 C [131 F] for EPA Tier 2 equivalent machines)

COLD WEATHER
- Antifreeze, –50° C (–58° F)
- 120V or 240V coolant heating elements (recommended in conditions from –18° C to –30° C [0° F to –22° F])
- Fuel heater (heated by recirculation using engine heat and a heat exchanger) (recommended in conditions from –18° C to –30° C [0° F to –22° F])
- –40° C (–40° F) Hydraulic Oil, Arctic
- Heater Mirrors